Fritsch PULVERISETTE 25 Bedienungsanleitung

Operating Manual translation of the original FRITSCH Power Cutting Mill

page 9 PULVERISETTE 25 1.4 Brief Description of the Instrument 1.4.1 Applications The cutting mill can be used for rapid comminution of medium-hard,

page 10 PULVERISETTE 25 1.5 Technical Data 1.5.1 Dimensions 450 mm x 650 mm x 630 mm (width x depth x height) 1.5.2 Weight x 75 kg (net wei

page 11 PULVERISETTE 25 2 Operating Safety 2.1 General Safety Instructions x Read the operating instructions carefully before use. x The instrument

page 12 PULVERISETTE 25 2.3 Protective Equipment x Protective equipment must be used as intended and must not be rendered disabled or dismantled. x A

page 13 PULVERISETTE 25 2.4 Danger Points x The cover flap (6) can be lifted out of the hinges. When opening up the upper housing (2), it is possible

page 14 PULVERISETTE 25 2.5 Electrical Safety 2.5.1 General x Press the STOP button: the cutting mill will slow down and stop.x Set the main switch

page 15 PULVERISETTE 25 3 Installation 3.1 Unpacking x Remove the nails with which the protective packing is fastened on the transport pallet. x Lif

page 16 PULVERISETTE 25 3.5 Ambience conditions x Use the instrument only inside. x The air must not contain any electrical conductive dust. x The

page 17 PULVERISETTE 25 3.8 Switching On for the First Time / Test for Correct FunctioningFirst switch the instrument on when all of the tasks descri

page 18 PULVERISETTE 25 4 Working with the Cutting Mill 4.1 Preparation for Grinding 4.1.1 Opening the Cutting Mill 1. Set the main switch (19) on

PULVERISETTE 25 PULVERISETTE 25

page 19 PULVERISETTE 25 4.1.2.1 Stationary Knife Positions 4.1.2.2 Stationary Knife Positions with TC-Equipped Blade Important!!Note the position of

page 20 PULVERISETTE 25 4.1.3 Setting the Knife Gap Width The factory setting for the knife gap is approx. 0.5 mm. 1. Open the Cutting Mill (see ch

page 21 PULVERISETTE 25 4.1.4 Inserting / Changing a Rotor 1. Open the cutting mill (see chapter 4.1.1) 2. Pull the rotor (3) out to the front whil

page 22 PULVERISETTE 25 6. Close the cutting mill (see chapter 4.1.6) Caution! Check whether the rotor (3) turns freely (see chapter Fehler! Verweisq

page 23 PULVERISETTE 25 4.1.6 Closing the Cutting Mill 1. Before closing the cutting mill, clean the cutting chamber, the contact surfaces of the ho

page 24 PULVERISETTE 25 5. Unscrew the 3 screws holding the motor cover (14) in place. 6. Carefully push back the motor cover (14). 7. Disconnect

page 25 PULVERISETTE 25 9. Pull the funnel cable out of the angled screw coupling by sliding the clamping ring down and pulling the black cable guide

page 26 PULVERISETTE 25 4.1.7.3 Changing from the Protected Funnel to the Standard Funnel 1. Close the cutting mill. 2. Close the funnel lid (21).

page 27 PULVERISETTE 25 8. Carefully push back the motor cover (14). 9. Use a screwdriver to unscrew the cap covering the opening for running the f

page 28 PULVERISETTE 25 x Connect the funnel cable to terminals 2 and 2.1. 13. Position the motor cover (14) and screw it on. 14.Reconnect the cuttin

Edition 02/2002 Index 006PULVERISETTE 25 Fritsch GmbH Milling and Sizing Industriestrasse 8 D - 55743 Idar-Oberstein Phone: +49 (0)6784/ 70-0 Fax:

page 29 PULVERISETTE 25 4.3 Grinding Process with the Protected Funnel 1. Set the main switch (19) on the back of the instrument to I (ON). 2. Clos

page 30 PULVERISETTE 25 4.4 Overloading of the Cutting Mill During loading and during the downwards movements of the piston (23), attention should b

page 31 PULVERISETTE 25 7. Position the motor cover (14) and screw it on. 8. Reconnect the cutting mill to the mains. 9. Set the main switch (19) o

page 32 PULVERISETTE 25 aC245.3.2 Protected Funnel (22) 1. Set the main switch (19) on the back of the instrument to 0 (OFF).2. Pull the sample pushe

page 33 PULVERISETTE 25 5.3.2.2 Removing the Piston (23): 1. Open the funnel lid (21). 2. Use a screwdriver to unscrew the Phillips head screws (D)

page 34 PULVERISETTE 25 6 Maintenance During maintenance work that does not require a power supply, unplug the mains plug (20) and secure the instrume

page 35 PULVERISETTE 25

page 36 PULVERISETTE 25

page 37 PULVERISETTE 25 7 Warranty The warranty card enclosed with the device upon delivery must be completely filled out and returned to the deliveri

page 38 PULVERISETTE 25 9 Disclaimer Before using this product, these operating instructions are to be carefully read and be understood. Use of the pr

page 3 PULVERISETTE 25 Table of contents page1 General Information / Introduction...

page 39 PULVERISETTE 25 Fritsch GmbH expressly disclaims every explicit or implied, contractual or arising from improper handling or a fixed contractu

page 40 PULVERISETTE 25 10 List of keywords AApplications... 9 DDanger Points...

PULVERISETTE 25 PULVERISETTE 25

PULVERISETTE 25 PULVERISETTE 25

PULVERISETTE 25

page 4 PULVERISETTE 25 4 Working with the Cutting Mill ...

page 5 PULVERISETTE 25 1 General Information / Introduction 1.1 Basic DesignThe terms and numbering listed below are used to designate specific parts

page 6 PULVERISETTE 25 (1) standard funnel (14) motor cover (18) ventilation louver (20) mains plug (19) main switch (17) safety switches r(17) clamp

page 7 PULVERISETTE 25 1.2 Notes about Operating Instructions x The copyright to these technical documents is the property of Fritsch GmbH, Manufact

page 8 PULVERISETTE 25 1.3 Explanations of the signs at the instrument and in the operating instructions Attention!Warning against danger spot. Obser